Add parameter programming special function, support below programmable parameters:
9D: Road speed limit, mandated by law
AIS: Injector cylinder 1, calibration
AIT: Injector cylinder 2, calibration
AIU: Injector cylinder 3, calibration
AIV: Injector cylinder 4, calibration
AIW: Injector cylinder 5, calibration
AIX: Injector cylinder 6, calibration
AIZ: Fuel consumption, calibration percent
AJ: Diff RSL, enable/disable
AJM: Full load calibration, in production
AU: Max engine speed stationary
AZO: Enable High End Governor Engine Speed
AZQ: High gear ratio end governor engine speed
AZR: Max espd, gear ratio setting
AZS: Max espd, gear ratio for limited max espd
BNQ: Max engine speed at speed error
BNS: Governor mode
BNT: Overspeed limit
BNW: Overspeed shutdown
BNX: Oil temperature warning
BPA: Coolant temperature warning
BPD: Idle engine speed
BPG: Idle speed voltage
BPJ: Max speed voltage
BPM: Lamp test
BPN: Governor droop
BPQ: Preheat on ignition
BPR: Coolant level derate
BPS: Oil pressure derate
BPT: Coolant temperature derate
BPU: Governor gradient
BQA: Oil temperature derate
BQB: Boost temperature derate
BQF: Stop function EMS, Energized to
BQK: Exhaust temperature derating disabled
CNR: PTO governor gradient used
DKR: Injector class
DN: Cust data, Fleet ID
DV: Diff RSL, max vspd next highest gear
DX: Cust data, engine ECU password
DYG: Adjustment factor for high I-gain of espd governor
DYH: Adjustment factor for low I-gain of espd governor
DYI: Adjustment factor for low P-gain of espd governor
DYJ: Adjustment factor for low D-gain of espd governor
DYK: Adjustment factor for high P-gain of espd governor
DYL: Adjustment factor for high D-gain of espd governor
DYM: Enable flag for lower torque limit
ECQ: Crankcase pressure derating disabled
ECR: Piston cooling pressure derating disabled
ECT: Boost pressure derating disabled
EG: Engine oil temperature
FMF: Oil temperature derating disabled
FMG: Boost temperature derating disabled
FMH: Coolant level derating disabled
FMI: Oil pressure derating disabled
FMJ: Coolant temperature derating disabled
FSN: Oil temperature warning limit
FSO: Coolant temperature warning limit
FSQ: Cylinder balancing forced status
FVS: Engine Protection - Oil Pressure Shutdown
FVU: Engine Protection - Coolant Level Shutdown
FVW: Engine Protection- Coolant Temp Shutdown
FVY: Engine Protection- Trans Temp Shutdown
GFF: Total injected fuel quantity
GFG: Rail pressure set-point
GFH: PRV total opened time
GHA: Engine ProtectionOil Temp Shutdown
IAW: Stop fuel EMS, Energized to
ISD: Low battery alarm level
ITX: Enable Automatic At Speed Regeneration
ITY: Enable Inhibit Regeneration
ITZ: Enable Man Stat Regeneration
IUA: CM1 diag from Cluster
IUC: CM1 diag from DPF Smart Switch
IUE: Enable Man Moving Regeneration
IUI: Request reset when faulty component replaced
JAA: The PTO is drive shaft
JAC: Enable Manual Regen During PTO
JXC: PTO Governor Type
MUR: Enable High Pressure Fuel Pump Failure Diagnosis
NMI: DEF Dosing Injector Derating Disabled
NMW: Enable Energized To Run
PDC: Application Type Industrial
PDD: Application Type Marine
QHP: Battery Usage
RRA: E-key, Keyfob not Required, Enable
VIN: Vehicle Identification Number
YA: Idle speed, setting
...